The most effective way of reducing noise on your bike is to reduce chain-slap. STFU Bike was developed with Chris Kovarik (a.k.a. Karver) and is the best product on the market for this job. Included in the product are two adjustable Drivetrain Damping modules that mount to your swingarm. When your chain is installed through STFU it is encased in muted rubber - chain-slap still happens it just causes much less noise. Important note: When you install this product ensure the cable tie is pulled quite tight using pliers. Re-tighten the cable ties after every second ride for the first 10 rides as they tend to stretch. If the cable ties stretch too much the product can rotate and go through your spokes which will cause significant damage to it (but your wheel will be fine). Compatibility: Trail - Suits bikes with 1x gearing (single chain ring)  and 9 - 13 speed with up to a 52 tooth cassette DH 7 Speed - Suits 7 speed downhill bikes with up to a 26 tooth cassette DH 10 Speed - Designed around 10 speed shimano style downhill drive-train with up to a 32 tooth cassette. Suitable for 8-12 speed Installation:Instructions on how to install STFU Bike can be found on the STFU Bike website.

Read more less

Sometimes it feels like the primary purpose of chains is to slap your chainstay... They wreck your paint and make a hell of a racket! Apply this tape to your bike to reduce the damage done and quieten sounds made while you ride. These seem to do a much better job than plastic frame protectors! This tape is thick, moisture sealing and flame retardant - just in case you shred too hard. Each strip is 25mm wide and comes in whatever length you order. 50cm is plenty enough to apply to a chainstay. Make sure you measure up before purchasing so you know how much you need :)

Read more less

Sick of cable rattle inside your frame? Here's some tubing which fits over your internal cables and will stop them from rattling inside your frame. This tubing is 1m long, has an internal diameter of 5mm and an outer diameter of 10mm. If you order more than one unit, we will provide a length equal to the number of units. E.g. 2x units is 2m. This will allow you to get better use of the available tubing :)  Things to Note: A lot of bikes will require more than 1m so have a measure up first to decide how much you need before buying This tubing fits 4mm & 5mm cable well (almost all cables) It's worth looking at your cable entrances to assess suitability - some frames have extremely narrow cable entrances that you can't squish this through

Read more less

Angle Adjustable Housing Connectors are useful for tidying up the cockpit and reducing cable/hose rattle. They snap onto your cables easily and keep them parrallel to each other.  Once you've got your cables trimmed to roughly the right length, use a combination of these and rotatable connectors to keep the cables from smashing around too badly. There are a few different sizes, make sure you get the correct one! Sizing:4mm: most gear cables5mm: most hydraulic brake cables, some gear cables (much less common, we only sell 4mm outer diameter)  

Read more less

These Spiral Rubber Frame Protectors reduce and dampen vibration noise caused by the cables vibrating against the frame. They are made of a soft silicone which is good at staying put will significantly reduce any cable rub.  These Protectors are about 6cm long and a large enough diameter to fit around one cable. We tried tying two cables together with these but sadly the protector fell off, a different solution is required for that.     

Read more less

Sometimes it feels like the primary purpose of chains is to slap your chainstay... They wreck your paint and make a hell of a racket! The STFU Stay Guard is here to help with this issue. The Stay Guard is a low-profile protector that uses a tapered fin design to (much more silently) absorb chain slaps. Sticky as hell, it’s best applied to the top or bottom of your chain stays. Really keen to get rid of all noises? Consider using it on the bottom of your chain stay and pairing it with an STFU Bike Drivetrain Damper on top. At 400mm long (56mm wide x 12mm high), it’s long enough to cover the top of your chain stay, part of your seat stay and even a section of the bottom of your chain stay. You might even have some spare to give a mate whos bike needs a chill pill. In our opinion, this product is more effective than Marsh Guard slapper tape and comparable to VHS MTB tape. It is certainly more effective than the hard plastic chainstay protectors that come on many bikes and do very little to tone down the racket! Whilst this product does stick to your frame well, if your heel rubs your chainstay we recommend adding a zip tie (or two) to ensure it stays stuck on there in the long term.

Read more less