-
Slick gear cable inner - Stainless steel + crimps
Here's 2m of 1.1mm Stainless Steel Shift Cable made by Jagwire. It is suitable for SRAM and Shimano setups. It's been pre-stretched, so it doesn't stretch as much for you, and it's surface has been smoothed to ensure your shifting is low friction. On top of that, it's stainless steel so it won't corrode. Also included is two cable end caps - just in case. You even get to choose what colour they are! :)
$5.99
-
Gear cable outer housing with Slick lube + ferrules
Here's some Jagwire 4mm Slick-lube gear housing, suitable for SRAM and Shimano setups. In the centre is a long lasting slick lubricant that reduces shifting friction and reduces water penetration. Encompassing that are strands of wire which reduce the chance of the housing kinking and messing up your shifting. All of this makes for a low friction and long lasting gear housing! We sell this in 2m and 10m lengths. 2m will do a long cable for all non-tandem bikes (except extra extra extra long bikes). 10m is slightly cheaper per metre, but you also get much better usage of cable (less wastage, so even cheaper again). And to top it off, we include some ferrules for your cable. If you need some more ferrules, have a look here. Offcuts: The 50 metre rolls we purchase aren't quite 50 metres after all... Instead of binning the small bit at the end, we offer it for you to purchase. We don't stock these lengths as standard, it's only if a bit is cut off. A 1-1.5m offcut will be somewhere between 1m and 1.5m long, the same is true for other lengths of offcuts. Please don't email us asking when we will have offcuts in stock next 😅 Other notes: Gear housing comes in 4mm and 5mm diameters. You can use either as long as you use the right ferrules! This cable is 4mm in diameter since it is most common Your housing may need a few days to relax after being opened, it may have been stored in a circle for a while...
$5.99- $44.99
-
Brake cable inner - Stainless steel + crimps
Here's 2m of 1.5mm Stainless Steel Brake Cable made by Jagwire. It is suitable for SRAM and Shimano setups. It's been pre-stretched, so it doesn't stretch as much for you, and it's surface has been smoothed to ensure your shifting is low friction. On top of that, it's stainless steel so it won't corrode. Also included is two cable end caps - just in case. You even get to choose what colour they are! :) We offer two types of brake cables Road and MTB. The difference between the two is the shape of cable head. Below is an image which you can use to decide which type you need.
$5.99
-
DMR DeathGrip Flangeless Lock-On Grips
DMR Deathgrips are our favorite grips because of their waffle pattern and knurling that provide excellent grip. Additionally, they feature a mushroom on the inner side for added comfort. If you have large hands or prefer a softer grip, choose the thicker version. However, if you prefer a more direct feel of your front wheel, opt for the thinner version. We offer both flanged and flangeless versions of Deathgrips; this is the flangeless version. Fancy a bling pair? Pay a little extra and get custom colour collars!
$49.99- $79.99
-
Cable End Cap (Crimp)
Rock that custom colour scheme with 1.8mm cable end caps in a variety of colours 😊
$0.49- $2.99
-
DMR DeathGrip Refill Grips
DMR Deathgrips are our favorite grips because of their waffle pattern and knurling that provide excellent grip. Additionally, they feature a mushroom on the inner side for added comfort. If you have large hands or prefer a softer grip, choose the thicker version. However, if you prefer a more direct feel of your front wheel, opt for the thinner version. We offer both flanged and flangeless versions of Deathgrips. This is a pair of refill grips. They do not come with collars, you will need to use your own collars from your last pair :)
$39.99
-
Brake cable outer housing with Slick lube
Here's 2m of Jagwire 5mm diameter Slick-lube Brake housing, suitable for SRAM and Shimano setups. In the centre is a long lasting slick lubricant that reduces shifting friction and reduces water penetration. Encompassing that within the housing is a steel coil for improved stiffness for braking. All of this makes for a high performance and long lasting brake housing! We sell this in 2m and 10m lengths. 2m will do a long cable for all non-tandem bikes (except extra extra extra long bikes). 10m is slightly cheaper per metre, but you also get much better usage of cable (less wastage, so even cheaper again). We don't include ferrules with brake cables because different models of brakes use different numbers of ferrules. We do suggest that you replace your ferrules each time you replace a cable though, so if you need some you can grab them here. Make sure you grab the brake version! Please note: Your housing may need a few days to relax after being opened, it may have been stored in a circle for a while... Offcuts: The 50 metre rolls we purchase aren't quite 50 metres after all... Instead of binning the small bit at the end, we offer it for you to purchase. We don't stock these lengths as standard, it's only if a bit is cut off. A 1-1.5m offcut will be somewhere between 1m and 1.5m long, the same is true for other lengths of offcuts. Please don't email us asking when we will have offcuts in stock next 😅
$9.99- $36.99
-
Cable Rattle Damper Tubing - 1m
Sick of cable rattle inside your frame? Here's some tubing which fits over your internal cables and will stop them from rattling inside your frame. This tubing is 1m long, has an internal diameter of 5mm and an outer diameter of 10mm. If you order more than one unit, we will provide a length equal to the number of units. E.g. 2x units is 2m. This will allow you to get better use of the available tubing :) Things to Note: A lot of bikes will require more than 1m so have a measure up first to decide how much you need before buying This tubing fits 4mm & 5mm cable well (almost all cables) It's worth looking at your cable entrances to assess suitability - some frames have extremely narrow cable entrances that you can't squish this through
$9.99
-
DMR DeathGrip Flanged Lock-On Grips
DMR Deathgrips are our favorite grips because of their waffle pattern and knurling that provide excellent grip. Additionally, they feature a mushroom on the inner side for added comfort. If you have large hands or prefer a softer grip, choose the thicker version. However, if you prefer a more direct feel of your front wheel, opt for the thinner version. We offer both flanged and flangeless versions of Deathgrips; this is the flanged version. Fancy a bling pair? Pay a little extra and get custom colour collars!
$49.99- $79.99
-
Anti-kink Gear Cable End
We've always had issues with the ferrules used for our dropper posts. When you put your dropper post into your frame it's all too easy to kink the end cap (ferrule) and be left with a bad section of cable which leads to crappy shifting. Conveniently, anti-kink cable ends solve this problem. This Jagwire anti-kink gear cable end provides the end of cable flexibility required for dropper posts (and folding bikes) so that you're not caught out by a crappy connection to an important component. It fits to standard size gear outer cable (4mm) and is worth having laying around for the required situation.
$3.99
-
GPVN lock-on grips - type 1
For something that wears out all of the time, replacing grips can get really expensive. The feel of grips is also such a personal thing, we all seem to like something different. We held off sourcing grips for a long time not quite sure what strategy to take. We've decided the best strategy is just to source a few good options and let you guys decide which option/s appeal most to you. Of course we've done some vetting, we wouldn't sell you anything that was crap. The type 1 GPVN (Great Price, Very Nice) grips have double profile design which consists of a waffle pattern, which helps reduce vibrations, and a webbed pattern which provides good traction for your digits. They are 130mm long, have a diameter of of 30mm (reasonably thin) and use a single lockring. The end of the grip is covered in rubber so you can run your pinky finger in the danger position over the end (why on earth do we do this?). There's a review of a remarkably similar product here. We can guarantee that this is product of reasonable quality. If you were to have any issues please get in touch with us, though we can't provide a refund just because they're not your favourite style.
$19.99
-
DMR Deathgrip 1 Collars
Fan of DMR Deathgrips? Why not bling them out with some custom collars? Not compatible with deathgrip 2.
$19.99- $32.99
